PSP Errors Guide

[NightCalyster]

I hope this list will help you solve your errors by finding out what is the error in the first place.

Note: ctrl + F will make your search much quicker and faster.

Note: DC8 will solve all these errors. Unless its hardware failure(You will have to get a replacement for the hardware.


Normal Errors

The first 4 numbers gives information about the place of the error: 8002XXXX = Kernel 8001XXXX = The standard libc

00000001 = Internal Error

1. Reset your settings to default
2. Theres no WiFi point found

80020148 = The game could not be started If you're under an Official Firmware you can't run homebrew, downgrade/upgrade to an
Custom Firmware.

8002013C = Error in the flash memory of the PSP. Try to restore your flash0-backup or re-install the Custom Firmware.

80020321 = The game could not be started Check if you configured kernel
or UMD/ISO mode right.

8008273A = Internal Error Reset your settings to default

80108D50 = PSP Camera not connected

80410A0B = Hardware Error WiFi is damaged.

IDstorage Errors

DRNFFFFFFD8 = key 0x4 missing DRNFFFFFFD7 = key 0x4 header is not "n y r B" (in hex: 6E 79 72 42)

DRNFFFFFFCE = key 0x5 missing DRNFFFFFFCD = key 0x5 header is not "g k l C" (in hex: 67 6B 6C 43)

DRNFFFFFFC4 = key 0x6 missing DRNFFFFFFC3 = key 0x6 header is not "r d D M" (in hex: 72 64 44 4D)


Errors with TA-086 PSP motherboards:

DRNFFFFFFB9 = key 0x7 header is not "D a P A" (in hex: 44 61 50 41)

DRNFFFFFFB0 = key 0x8 missing DRNFFFFFFAF = key 0x8 header is not "p D C L" (in hex: 70 44 43 4C)

You can repair this with IdStorage Manager or Using DC8.

For key 08 errors make a new key 08 by adding this line: "70 44 43 4C 01 00 00 00 0C 00 00 00 76 FC 19 C8 0A 00 19 00 10 00 0D 00 07 00 02" and than 00 untill the end.

CTA80000025 = region key (0x0100) is damaged or missing (You only can repair this with your OWN backup).

Error List

• UKN9000001 = The update cannot be started. The data is corrupted.
• 80110305 = Load failed.The Memory Stick™ could not be acessed.
• 80010013 = device / media not found
• 8001B002 = unknown
• 80020001 or 800244C = kernel errors
• 80020001 = generic kernel error (default)
• 800200D9 = failed to allocate the memory block
• 80020130 = file read error
• 80020148 = PRX type unsupported
• 80110482 = occurs when test of WLAN infrastructure connection fails
• FFFFFED3 = unknown (might be decryption error)
• 80410001 or 80410D16 = network errors
• 80410D07 = unknown (possibly WLAN)
• ffffffff = PSP update failed
• 80410A0B = Internal Error
• 8041040F = DNS Error, unable to connect to server
• 80410410 = Cannot connect to the given acess point
• 80010087 = The game could not be started
• 0x0 = no error
• 0x80020001 = error
• 0x80020002 = not implemented
• 0x80020032 = illegal exception code
• 0x80020033 = exception handler not use
• 0x80020034 = exception handler already used
• 0x80020035 = system call table notuse
• 0x80020036 = system call table alraady used
• 0x80020037 = illegal system call table
• 0x80020038 = illegal Primary Syscall number
• 0x80020039 = Primary Syscall number already use
• 0x80020064 = call from interrupt handler/thread
• 0x80020065 = illegal INTRCODE
• 0x80020066 = CPU already interrupt disable
• 0x80020067 = Handler already exist
• 0x80020068 = Handler not found
• 0x80020069 = illegal interrupt level
• 0x8002006a = illegal address
• 0x8002006b = illegal IntrHandler Option Paramsize
• 0x8002006c = illegal stackad dress
• 0x8002006d = alreadystackad dressset
• 0x80020096 = not found free Hard Timer
• 0x80020097 = illegal timer ID
• 0x80020098 = illegal source
• 0x80020099 = illegal prescale
• 0x8002009a = Hard Timer in use
• 0x8002009b = Hard Timer not setup
• 0x8002009c = Hard Timer not in use
• 0x800200a0 = unit number already used
• 0x800200a1 = unit number notused
• 0x800200a2 = rom directory notfound
• 0x800200c8 = id type already exist
• 0x800200c9 = id type not exist
• 0x800200ca = {not available}
• 0x800200cb = unknown UID
• 0x800200cc = unmatch UID type
• 0x800200cd = id not exist
• 0x800200ce = not found UID function
• 0x800200cf = UID already holder
• x800200d0 = UID not holer
• 0x800200d1 = illegal permission
• 0x800200d2 = illegal argument
• 0x800200d3 = illegal adress
• 0x800200d4 = the memory area is out ofrange
• 0x800200d5 = the memory areais over lap
• 0x800200d6 = illegal partitionid
• 0x800200d7 = partition in use
• 0x800200d8 = illegal memory block allocation type
• 0x800200d9 = failed toal loca the memory block
• 0x800200da = inhibitedtores izethismemoryblock
• 0x800200db = failedtoresize thismemoryblock
• 0x800200dc = failedtoalloca teheapblock
• 0x800200dd = failedtoalloca teheap
• 0x800200de = illegalchunkid
• 0x800200df = cannotfindchun kname
• 0x800200e0 = thereisnofreec hunk
• 0x8002012c = modulelinkerro r
• 0x8002012d = illegalobjectf ormat(notPRX/PFX)
• 0x8002012e = notfoundModule
• 0x8002012f = notfoundModule file
• 0x80020130 = Modulefileread error
• 0x80020131 = memoryinuse
• 0x80020132 = partitionmisma tch
• 0x80020133 = modulealreadys tarted
• 0x80020134 = modulenotstart edyet
• 0x80020135 = modulealreadys topped
• 0x80020136 = modulecannotst op
• 0x80020137 = modulenotstopp edyet
• 0x80020138 = modulecannotre move
• 0x80020139 = exclusiveload
• 0x8002013a = Libraryisnotli nkedyet
• 0x8002013b = Libraryalready exists
• 0x8002013c = Librarynotfoun d
• 0x8002013d = illegalLibrary header
• 0x8002013e = Libraryisusedn ow
• 0x8002013f = modulealreadys topping
• 0x80020140 = illegaloffsetv alue
• 0x80020141 = illegalpositio ncode
• 0x80020142 = illegalaccessc ode
• 0x80020143 = modulemanagerb usy
• 0x80020144 = illegalflag
• 0x80020145 = cannotgetmodul elist
• 0x80020146 = prohibitLoadMo duledevice
• 0x80020147 = prohibitLoadEx ecdevice
• 0x80020148 = unsupportedPRX type
• 0x80020149 = illegalpermiss ioncall
• 0x8002014a = cannotgetmodul einformation
• 0x8002014b = illegalLoadExe cbuffer
• 0x8002014c = illegalLoadExe cfilename
• 0x8002014d = Thereisnoexitc allback
• 0x80020190 = nomemory
• 0x80020191 = illegalattrpar ameter
• 0x80020192 = illegalthreade ntryaddress
• 0x80020193 = illegalpriorit yvalue
• 0x80020194 = illegalstacksi ze
• 0x80020195 = illegalmode
• 0x80020196 = illegalmask
• 0x80020197 = illegalthreadI D
• 0x80020198 = notfoundthread
• 0x80020199 = notfoundsemaph ore
• 0x8002019a = notfoundeventf lag
• 0x8002019b = notfoundmessag ebox
• 0x8002019c = notfoundVpool
• 0x8002019d = notfoundFpool
• 0x8002019e = notfoundmessag epipe
• 0x8002019f = notfoundalarm
• 0x800201a0 = notfoundthread eventhandler
• 0x800201a1 = notfoundcallba ck
• 0x800201a2 = threadalreadyD ORMANT
• 0x800201a3 = threadalreadyS USPEND
• 0x800201a4 = threadisnotDOR MANT
• 0x800201a5 = threadisnotSUS PEND
• 0x800201a6 = threadisnotWAI T
• 0x800201a7 = nowdispatchdis abled
• 0x800201a8 = WAITtimeout
• 0x800201a9 = WAITcanceled
• 0x800201aa = WAITstatusrele ased
• N0x800201ab = WAITstatusrel easedwithcallback
• 0x800201ac = threadistermin ated
• 0x800201ad = semaphorecount erzero
• 0x800201ae = semaphorecount eroverflow
• 0x800201af = eventflagcondi tionnotoccur
• 0x800201b0 = thiseventflagc annotacceptwaitswithmulti plethreads
• 0x800201b1 = illegaleventfl agwaitpattern
• 0x800201b2 = messageboxhave nomessage
• 0x800201b3 = messagepipeisf ull
• 0x800201b4 = messagepipeise mpty
• 0x800201b5 = waitobjectdele ted
• 0x800201b6 = illegalmemoryb lock
• 0x800201b7 = illegalmemorys ize
• 0x800201b8 = illegalscratch padaddress
• 0x800201b9 = scratchpadinus e
• 0x800201ba = scratchpadnoti nuse
• 0x800201bb = illegaltype
• 0x800201bc = illegalsize
• 0x800201bd = illegalcount
• 0x800201be = notfoundvtimer
• 0x800201bf = illegalvtimerI D
• 0x800201c0 = illegalKTLSID
• 0x800201c1 = KTLSisfull
• 0x800201c2 = KTLSisbusy
• 0x80020258 = invalidsuchpri ority
• 0x80020259 = devicenameisin valid
• 0x8002025a = devicenameisun known
• 0x8002025b = pminformationi sregisteredalready
• 0x8002025c = pminformationi snotregistered
• 0x8002025d = majorstateisin validvalue
• 0x8002025e = requestisinval id
• 0x8002025f = requestisunkno wn
• 0x80020260 = unitnumberisin valid
• 0x80020261 = cannotcancelre quest
• 0x80020262 = pminformationi sinvalid
• 0x80020263 = argumentisinva lid
• 0x80020264 = alreadytargete powerstate
• 0x80020265 = failedtochange systempowerstate
• 0x80020266 = cannotchangede vicepowerstate
• 0x80020267 = devicedoesnots upportsuchpowerstate
• 0x800202bc = requesttotheDM ACfailed
• 0x800202bd = DMAoperationis lessorequalone
• 0x800202be = theoperationis alreadyqueued
• 0x800202bf = theoperationis alreadyfinishedornotqueue ud
• 0x800202c0 = theoperationis alreadyintransferprogress
• 0x800202c1 = theoperationis notassignedyet
• 0x800202c2 = thesyncoperati ontimedout
• 0x800202c3 = dmaoperationst ructisalreadyfreed
• 0x800202c4 = dmaoperationis used
• 0x800202c5 = dmaoperationis empty
• 0x800202c6 = DMAoperationis aborted
• 0x800202c7 = DMAoperationis error
• 0x800202c8 = physicalDMAcha nnelisalreadyreserved
• 0x800202c9 = physicalDMAcha nnelisnotmanagedbydmacman ager
• 0x800202ca = thereisaprivil egeaddressinlinklist
• 0x800202cb = linklistbuffer isnotenough
• 0x800202cc = theoperationis notassignedtophysicalDMAc hannel
• 0x800202cd = theoperationis childoperation
• 0x800202ce = itistoomuchtha ntransferabledatasize
• 0x800202cf = argumentisinva lid
• 0x80020320 = Toomanyopenfil es
• 0x80020321 = Nosuchdevice
• 0x80020322 = Cross-devicelink
• 0x80020323 = Badfiledescrip tor
• 0x80020324 = Invalidargumen t
• 0x80020325 = Unsupportedope ration
• 0x80020326 = Aliasisalready used
• 0x80020327 = Cannotmount
• 0x80020328 = Driverdeleted
• 0x80020329 = Asyncoperation isbusy
• 0x8002032a = Noasyncoperati on
• 0x8002032b = Deviceisalread yregistered
• 0x8002032c = Nocurrentworki ngdirectory
• 0x8002032d = Filenametoolon g
• 0x800203e8 = DECI3Nosuchdev iceoraddress
• 0x800203e9 = DECI3I/Oerror
• 0x800203ea = DECI3Notenough core
• 0x800203eb = STDIOnotopened
• 0x8002044c = Parameterisnot cachealigned
• 0x8002044d = Endofkernelerrorcode.Neverusethisname
• CA000005 - keys.bin not found when trying to run a PS1 game.
• DADADADA - Running a FW Update in DAX custom FW
• FFFFFFFF - PSP update failed
• UKN9000001 - update cant start, data corrupt
• 00000001 - WiFi error. Occurs when no access points are detected in official 3.7X and custom 3.7X firmware.

• 80010087 - Error reading UMD or UMD not present
• 80110305 - Load failed.The Memory Stick could not be acessed
• 80020148 - Unsupported PRX type | This error also seems to appear when you are running an iso with a fake mem. stick

• 8001006F - Remote Play connection error. Most likely when no PS3 is sending a signal over your network.

• 800200D1 - Ran homebrew without Homebrew enabled firmware.
• 8002014C - Ran kxploited homebrew without Homebrew enabled firmware.

• 80020321 - Ran a game that doesn't support NO-UMD* (DAX FW ONLY!)

• 80110404 - Network error, try restore default settings to fix
• 80000004 - its just a general error code that the PSP spits out when it doesnt understand something could mean anything

• 80110307 - Load Failed There is no Data available
• 80010002 - Putting the POPS EBOOT in the wrong folder
• 80000001 - Got it when trying to run PSP filer version 3.6 on 3.40* firmware

• 80410A0B - Loose WiFi card
• 80020321 - No umd in drive when no umd is disabled
• 80110305 = Load failed.The Memory Stick could not be acessed
• 8001006F - Remote Play connection error. Most likely when no PS3 is sending a signal over your network

• 80020148 - Unsupported PRX type
• 800200D1 - Ran homebrew without Homebrew enabled firmware
• 8002014C - Ran kxploited homebrew without Homebrew enabled firmware

• 80020321 - No umd in drive when no umd is disabled / Ran a game that doesn't support NO-UMD / "No-UMD Mode"

• 98765432 - Selected a language who's font has been removed. DAX FW ONLY ERROR!

• 80020148 - (unsupported PRX type)?
• 800201A8 - (WAIT timeout)?
• 80020130 - File Read Error (ex. length is 0)
• 80020001 - Generic Kernel Error - default (ex. executable is invalid)
• 800200D9 - Failure to allocate memory block (ex. missing PSP)
• 80410D07 - Connection error has occurred. (Ie cant find access pt)
• 80020001 - error
• 80020002 - not implemented
• 80020032 - illegal exception code
• 80020033 - exception handler not use
• 80020034 - exception handler already used
• 80020035 - system call table not use
• 80020036 - system call table already used
• 80020037 - illegal system call table
• 80020038 - illegal Primary Syscall number
• 80020039 - Primary Syscall number already use
• 80020064 - call from interrupt handler/thread
• 80020065 - illegal INTRCODE
• 80020066 - CPU already interrupt disable
• 80020067 - Handler already exist
• 80020068 - Handler not found
• 80020069 - illegal interrupt level
• 8002006a - illegal address
• 8002006b - illegal Intr Handler Option Param size
• 8002006c - illegal stack address
• 8002006d - already stack address set
• 80020096 - not found free Hard Timer
• 80020097 - illegal timer ID
• 80020098 - illegal source
• 80020099 - illegal prescale
• 8002009a - Hard Timer in use
• 8002009b - Hard Timer not setup
• 8002009c - Hard Timer not in use
• 800200a0 - unit number already used
• 800200a1 - unit number not used
• 800200a2 - rom directory not found
• 800200c8 - id type already exist
• 800200c9 - id type not exist
• 800200ca - {not available}
• 800200cb - unknown UID
• 800200cc - unmatch UID type
• 800200cd - id not exist
• 800200ce - not found UID function
• 800200cf - UID already holder
• x800200d0 - UID not holder
• 800200d1 - illegal permission
• 800200d2 - illegal argument
• 800200d3 - illegal address
• 800200d4 - the memory area is out of range
• 800200d5 - the memory area is overlap
• 800200d6 - illegal partition id
• 800200d7 - partition in use
• 800200d8 - illegal memory block allocation type
• 800200d9 - failed to allocate memory block
• 800200da - inhibited to resize this memory block
• 800200db - failed to resize this memory block
• 800200dc - failed to allocate heap block
• 800200dd - failed to allocate heap
• 800200de - illegal chunk id
• 800200df - cannot find chunk name
• 800200e0 - there is no free chunk
• 8002012c - module link error
• 8002012d - illegal object format (not PRX/PFX)
• 8002012e - not found Module
• 8002012f - not found Module file
• 80020130 - Module file read error
• 80020131 - memory in use
• 80020132 - partition mismatch
• 80020133 - module already started
• 80020134 - module not started yet
• 80020135 - module already stopped
• 80020136 - module cannot stop
• 80020137 - module not stopped yet
• 80020138 - module cannot remove
• 80020139 - exclusive load
• 8002013a - Library is not linked yet
• 8002013b - Library already exists
• 8002013c - Library not found
• 8002013d - illegal Library header
• 8002013e - Library isused now
• 8002013f - module already stopping
• 80020140 - illegal off set value
• 80020141 - illegal position code
• 80020142 - illegal access code
• 80020143 - module manager busy
• 80020144 - illegal flag
• 80020145 - cannot get module list
• 80020146 - prohibit Load Module device
• 80020147 - prohibit Load Exec device
• 80020148 - unsupported PRX type
• 80020149 - illegal permission call
• 8002014a - cannot get module information
• 8002014b - illegal Load Exec buffer
• 8002014c - illegal Load Exec file name
• 8002014d - There is no exit callback
• 80020190 - no memory
• 80020191 - illegal attr parameter
• 80020192 - illegal thread entry address
• 80020193 - illegal priority value
• 80020194 - illegal stack size
• 80020195 - illegal mode
• 80020196 - illegal mask
• 80020197 - illegal thread ID
• 80020198 - not found thread
• 80020199 - not found semaphore
• 8002019a - not found event flag
• 8002019b - not found message box
• 8002019c - not found Vpool
• 8002019d - not found Fpool
• 8002019e - not found message pipe
• 8002019f - not found alarm
• 800201a0 - not found thread event handler
• 800201a1 - not found callback
• 800201a2 - thread already DORMANT
• 800201a3 - thread already SUSPEND
• 800201a4 - thread is not DORMANT
• 800201a5 - thread is not SUSPEND
• 800201a6 - thread is not WAIT
• 800201a7 - now dispatch disabled
• 800201a8 - WAIT timeout
• 800201a9 - WAIT canceled
• 800201aa - WAIT status released
• N800201ab - WAIT status released with callback
• 800201ac - thread is terminated
• 800201ad - semaphore counter zero
• 800201ae - semaphore counter overflow
• 800201af - event flag condition not occur
• 800201b0 - this event flag cannot accept waits with multiple threads
• 800201b1 - illegal event flag wait pattern
• 800201b2 - message box have no message
• 800201b3 - message pipe is full
• 800201b4 - message pipe is empty
• 800201b5 - wait object deleted
• 800201b6 - illegal memory block
• 800201b7 - illegal memory size
• 800201b8 - illegal scratchpad address
• 800201b9 - scratch pad in use
• 800201ba - scratchpad not in use
• 800201bb - illegal type
• 800201bc - illegal size
• 800201bd - illegal count
• 800201be - not found vtimer
• 800201bf - illegal vtimer ID
• 800201c0 - illegal KTLS ID
• 800201c1 - KTLS is full
• 800201c2 - KTLS is busy
• 80020258 - invalid such priority
• 80020259 - device name is invalid
• 8002025a - device name is unknown
• 8002025b - pm information is registered already
• 8002025c - pm information is not registered
• 8002025d - major state is invalid value
• 8002025e - request is invalid
• 8002025f - request is unknown
• 80020260 - unit number is invalid
• 80020261 - cannot cancel request
• 80020262 - pm information is invalid
• 80020263 - argument is invalid
• 80020264 - already target epower state
• 80020265 - failed to change system power state
• 80020266 - cannot change device power state
• 80020267 - device does not support such power state
• 800202bc - request to the DMAC failed
• 800202bd - DMA operation is less or equal one
• 800202be - the operation is already queued
• 800202bf - the operation is already finished or not queueud
• 800202c0 - the operation is already in transfer progress
• 800202c1 - the operation is not assigned yet
• 800202c2 - the sync operation timed out
• 800202c3 - dma operation struct is already freed
• 800202c4 - dma operation is used
• 800202c5 - dma operation is empty
• 800202c6 - DMA operation is aborted
• 800202c7 - DMA operation is error
• 800202c8 - physical DMA channel is already reserved
• 800202c9 - physical DMA channel is not managed by dmac manager
• 800202ca - there is a privilege address in link list
• 800202cb - link list buffer is not enough
• 800202cc - the operation is not assigned to physical DMA channel
• 800202cd - the operation is child operation
• 800202ce - it is too much than transferable datasize
• 800202cf - argument is invalid
• 80020320 - Too many open files
• 80020321 - No such device
• 80020322 - Cross-device link
• 80020323 - Bad file descriptor
• 80020324 - Invalid argument
• 80020325 - Unsupported operation
• 80020326 - Alias is already used
• 80020327 - Cannot mount
• 80020328 - Driver deleted
• 80020329 - Async operation is busy
• 8002032a - No async operation
• 8002032b - Device is already registered
• 8002032c - No current working directory
• 8002032d - Filename too long
• 800203e8 - DECI3 No such device or address
• 800203e9 - DECI3 I/O error
• 800203ea - DECI3 Not enough core
• 800203eb - STDIO not opened
• 8002044c - Parameter is not cache aligned
• 8002044d - End of kernel error code Never use this name

Thanks again to Dark-Alex for his wonderful find.

[Kalitrius]

THANKZ...nice guide to the various errors on a psp. SOMEONE STICK THIS UP!!!!!

[NightCalyster]

Thanks i actually made this thread to help people. Same with the OFW thread i found that people needed just this morning i was convinced that i should make it. So if this deserves a sticky then let it be.

[stuart93]

Hmm yeah, some threads on google basically the same as this but thanks anyway; this would be very useful to someone.

Sticky?

[leo9891]

Night didn't make this... he stole this from me!

its right here

lol nice guide btw!

[NightCalyster]

Originally Posted by leo9891

Night didn't make this... he stole this from me!

its right here

lol nice guide btw!

Lol. You almost made me feel stupid for a second for making another thread alike.

[Peza]

It's now officially stuck!

[Psyko]

Nice guide. Not only is it a sticky but bookmarked as well.

And of course, I have a suggestion. Why don't we make all the current stickies unstuck after Karothacker put them in his thread? It'll save us a lot of space...

[gigoo25]

WOW awsome guide!! Thanks!!

[leo9891]

Originally Posted by Psyko

Nice guide. Not only is it a sticky but bookmarked as well.

And of course, I have a suggestion. Why don't we make all the current stickies unstuck after Karothacker put them in his thread? It'll save us a lot of space...

cause KarotHacker's thread is not in every thread, and i like the idea of the stickies being stuck where they are at right now. and KarotHacker's thread isn't updated every so often.